Laboratory study on micro suspension emulsion plugging agent

  • DUAN Yue ,
  • HOU Changbing ,
  • ZHENG Rongcai ,
  • WANG Haihong ,
  • WANG Changyong
Expand
  • 1. Petroleum Production Engineering Research Institute, PetroChina Huabei Oilfield Company, Renqiu 062552, China; 2. Drilling Technology Research Institute, CNPC Bohai Drilling Engineering Co. Ltd., Renqiu 062552, China; 3. Borehole Operation Division, CNPC Bohai Drilling Engineering Co. Ltd., Renqiu 062552, China

Online published: 2013-11-26

Abstract

It is recognized that the normal chemical plugging agent cannot plug water and control profile effectively in formations with permeability ratio data more than three. Stable oil-in-water micro suspension emulsion (grain size 1~5 μm) was prepared from main material oil-soluble resin, emulsifier and stabilizer through disperse mill. The optimal formula was determined as follows: 50%~60% resin +0.35%~0.40% octadecyl trimethyl ammonium chloride or 0.35%~ 0.40% sodium benzenesulfonat +0.1% CMC +0.10%~0.15% calcium chloride +1%~5% SL+ water. Demulsifier formulation were also determined, 2%~3% aqueous solution of sodium hydroxide and 3%~5% calcium chloride solution were used for cationic emulsion and anionic emulsion corresponding. Viscosity, electron microscopy analysis of grain size, acid solubility, oil solubility tests were also carried out. Performance test shows that it has high temperature range and good injection and selectivity performance. Core flooding test shows that the breakthrough pressure gradient was 26 MPa/m, the plugging rate is greater than 97%, it kept high plugging rate after large amount of water flooding and it had good profile control performance for heterogeneous reservoir with the permeability ratio data being of seven.

Cite this article

DUAN Yue , HOU Changbing , ZHENG Rongcai , WANG Haihong , WANG Changyong . Laboratory study on micro suspension emulsion plugging agent[J]. Lithologic Reservoirs, 2013 , 25(6) : 112 -116 . DOI: 10.3969/j.issn.1673-8926.2013.06.021

References

[1] 李宇乡,唐孝芬,刘双成.我国油田化学堵水调剖剂开发和应用现状[J].油田化学,1995,12(1):88-94.
[2] 杨延辉,崔凯,王晓芬,等.华北油田砂岩油藏调水增油开发技术政策优化[J].石油钻采工艺,2009,31(增刊1):101-105.
[3] 蔡志刚,张满库,胡海燕,等.华北油田低渗透断块油藏改善开发效果配套开采技术[J].石油钻采工艺,1996,18(2):62-69.
[4] 殷艳玲,张贵才.化学堵水调剖剂综述[J].油气地质与采收率,2003,10(6):64-66.
[5] 刘翔鹗,李宇乡.中国油田堵水技术综述[J].油田化学,1992,9(2):180-187.
[6] 熊春明,唐孝芬.国内外堵水调剖技术最新进展及发展趋势[J].石油勘探与开发,2007,34(1):83-88.
[7] 高玉军,马春宝,傅奎仕,等.高选择性乳化稠油堵水技术[J].油田化学,1997,14(3):224-229.
[8] 丁锐,孟凡涛.水基油溶性堵剂室内研究[J].油田化学,2001,18(2):120-123.
[9] 庄永斌,王伟松,孟照平. GB/T11543—2008 表面活性剂中、高黏度乳液的特性测试及其乳化能力的评价方法[S].北京:中国标准出版社,2008.
[10] 姜作贤,姜兴国,王自成,等. CJJ42—91 乳化沥青路面施工及验收规程[S].北京:中国建筑工业出版社,1991.
[11] 赵清民,吕静,李先杰,等.非均质条件下乳状液调剖机理[J].油气地质与采收率,2011,18(1):41-47.
[12] 曹毅,张立娟,岳湘安,等.非均质油藏微球乳液调驱物理模拟实验研究[J].西安石油大学学报:自然科学版,2011,26(2):49-55.
[13] 卢福申,曹书瑜,贺得才,等.凝胶颗粒调剖的模拟实验油气地质与采收率[J].油气地质与采收率,2004,11(6): 62-64.
[14] 李金权.改性石蜡选择性堵水技术研究与现场应用[J].特种油气藏,2007,14(4):78-80.
[15] 庞兴亮,高飞,李国栋,等.乳化沥青制备和应用中的稳定性分析[J].河北工程技术高等专科学校学报,2001,9(3):15-17.
[16] 王丽娜,范维玉,南国枝,等.沥青乳化剂及沥青乳液性能研究[J].中国石油大学学报:自然科学版,2002,26(6):100-109.
[17] 张小英,高琦琳. GB/T4509—2010 沥青针入度测定法[S].北京:中国标准出版社,2011.
Outlines

/