关于泡沫油黏度的若干问题

doi:10.3969/j.issn.1673-8926.2016.04.001

岩性油气藏 ›› 2016, Vol. 28 ›› Issue (4): 1–8.doi: 10.3969/j.issn.1673-8926.2016.04.001

• 论坛与综述 • 下一篇

关于泡沫油黏度的若干问题

熊钰，王冲

西南石油大学石油与天然气工程学院，成都610500

出版日期:2016-07-20 发布日期:2016-07-20
作者简介:熊钰（1968-），男，博士，教授，现主要从事油气藏工程、油气藏流体相态理论与测试以及注气提高采收率方面的教学与研究工作。地址：（610500）四川省成都市西南石油大学石油与天然气工程学院明辨楼B530 室。E-mail：xiongyu_swpu@163.com。

Several issues concerning foamy oil viscosity

Xiong Yu，Wang Chong

School of Oil & Natural Gas Engineering，Southwest Petroleum University，Chengdu 610500，China

Online:2016-07-20 Published:2016-07-20

摘要/Abstract

摘要：

泡沫油现象被认为是加拿大和委内瑞拉一些稠油油藏在开采中出现异常高产和较高采收率的主要原因，对于泡沫油黏度的研究目前学术界尚无一致结论。针对泡沫油的黏度，主要从泡沫油黏度与异常高产之间的关系、泡沫油黏度模型以及泡沫油黏度的影响因素等3 个方面进行研究。压力衰竭速率、静置时间、测量装置、分散气体积分数、压力和流量、膨胀率和表面活性剂、分散气泡大小和剪切速率以及常规测试和非常规测试等对于泡沫油的黏度均有影响，目前学术界对于稠油泡沫油黏度的争议可能和这些影响因素有关,泡沫油黏度的测量问题可能是引起对泡沫油黏度争议的一个主要原因。泡沫油黏度的研究有利于澄清泡沫油的渗流机理，泡沫油的渗流机理对于稠油油藏数值模拟，尤其是稠油油藏注气开发过程中的优化设计均具有重要意义。

关键词: 水驱油田, 开发效果, 评价方法, 发展趋势

Abstract:

It is the foamy oil which was seemed as the main factor leading the unexpected high production and high recovery of some heavy oil reservoirs in Canada and Venezuela. When it comes to the issue of foamy oil viscosity,there are disputes about whether the viscosity is higher or not than that of the initial live oil. In order to get a better understanding of the issue, this paper carried out detailed investigation about the foamy oil viscosity on three aspects：the relationship between the viscosity and the unexpected high production, the viscosity model of foamy oil and the influencing factors of foamy oil viscosity. It is considered that the influencing factors of the foamy oil viscosity include the pressure depletion rate, stabilization time, measuring device, dispersed gas volume fraction, pressure and flow rate, expansion ratio, surfactant, the size of dispersed bubble, the shearing rate and the conventional or unconventional testing method, and the controversy of the foamy oil viscosity is relevant to these influencing factors,and it is mainly caused by the measuring of the viscosity. Furthermore, the seepage mechanism of foamy oil has important significance for heavy oil reservoir numerical simulation and the optimization design of gas injection for heavy oil reservoir.

Key words: water drive oilfield, development effect, evaluation method, development trend

熊钰，王冲. 关于泡沫油黏度的若干问题[J]. 岩性油气藏, 2016, 28(4): 1–8.

Xiong Yu，Wang Chong. Several issues concerning foamy oil viscosity[J]. Lithologic Reservoirs, 2016, 28(4): 1–8.

参考文献

［1］   牛嘉玉，刘尚奇，门存贵，等.稠油资源地质与开发利用［M］.北京：科学出版社，2002.

Niu Jiayu，Liu Shangqi，Men Cungui，et al. Resources，geology，development and utility of heavy oil［M］. Beijing：Science Press，2002.

［2］   汤明光，刘清华，张贵才，等.抗垢碱提高稠油采收率机理研究［J］.岩性油气藏，2014，26（3）：125-130.

Tang Mingguang，Liu Qinghua， Zhang Guicai，et al. Study on enhanc? ing heavy oil recovery mechanism of antiscaling alkali［J］. Lithologic Reservoirs，2014，26（3）：125-130.

［3］   翟亚梅，严玉圃，万永清，等.吐玉克油田深层稠油天然气吞吐技术研究与应用［J］.岩性油气藏，2012，24（4）：111-114.

Zhai Yamei，Yan Yupu，Wan Yongqing，et al. Research and applica? tion of gas huff and puff of deep heavy oil in the Tuyuke Oilfield［J］. Lithologic Reservoirs，2012，24（4）：111-114.

［4］   Firoozabadi A，Kashchiev D. Pressure and volume evolution during gas phase formation in solution gas drive process［J］. SPE Journal，1996，1（3）：219-228.

［5］   Alshmakhy A B. Foamy oil behaviour and heavy oil recovery：An xperimental approach［D］. Ottawa，University of Calgary：2011.

［6］   Smith G E. Fluid flow and sand production in heavy?oil reservoirs nder solution?gas drive［J］. SPE Production Engineering，1988，3（2）：169-180.

［7］   Sarma H，Maini B. Role of solution gas in primary production of eavy oils［R］. SPE 23631，1992.

［8］   Chen Zhangxin，Sun Jian，Wang R，et al. A pseudobubblepoint mdel and its simulation for foamy oil in porous media［J］. SPE Journal，2015，20（2）：239-247.

［9］   Bora R. Cold production of heavy oils：An experimental investigation of foamy oil flow in porous media［D］. Ottawa：University of algary，1998.

［10］   孙建平.疏松砂岩稠油油藏出砂冷采机理研究［D］.成都：西南石油大学，2005.

Sun Jianping. Study on cold production mechanisms of poorly con?solidated sandstone heavy oil reservoirs［D］. Chengdu：Southwest Petroleum University，2005.

［11］   Fisher D B，Espidel J，Huerta M，et al. Use of magnetic resonance imaging as a tool for the study of foamy oil behavior for an extra?heavy crude oil. T2/viscosity correlation with respect to rressure［J］. Transport in Porous Media，1999，35（2）：189-204.

［12］   Goodarzi N，Bryan J，Mai A，et al. Heavy?oil fluid testing with conven? tional and novel techniques［R］. SPE 97803，2005.

［13］   Islam M R，Chakma A. Mechanics of bubble flow in heavy oil reservoirs ［R］. SPE 20070，1990.

［14］   Albartamani N S. Experimental studies on “foamy oil” phenomena ［D］. Alberta：University of Alberta，2000.

［15］   Huerta M，Otero C，Rico A，et al. Understanding foamy oil mechanisms for heavy oil reservoirs during primary production［R］. SPE 36749， 1996.

［16］   Claridge E L，Prats M. A proposed model and mechanism for anoma?lous foamy oil behavior［R］. SPE 29243, 1994.

［17］   张艳玉，崔国亮，孙晓飞，等.考虑气相动态变化的泡沫油数值模拟研究［J］.油气地质与采收率，2014,21（4）：67-70.

Zhang Yanyu，Cui Guoliang，Sun Xiaofei，et al. Numerical simu?lation and analysis of foamy oil in consideration of the gas dynamic processes［J］. Petroleum Geology and Recovery Efficiency，2014， 21（4）：67-70.

［18］   Shen C， Batycky J P. Observations of mobility enhancement of heavy oils flowing through sand pack under solution sas drive［J］. Journal ofcanadian petroleum technology，1999，38（4）：46-53.

［19］   Sheng J J，Maini B B，Hayes R E，et al. Experimental study of foamy oil stability［J］. Journal ofcanadian petroleum technology，1997，36（4）：31-37.

［20］   Bauget F，Lenormand R. Mechanisms of bubble formation by pressure decline in porous media: a critical review［R］. SPE 77457, 2002.

［21］   Alshmakhy A B，Maini B B. Viscosity of foamy oils［R］. SPE 136665， 2010.

［22］   王伯军，吴永彬，蒋有伟，等.泡沫油PVT性质实验［J］.石油学报，2012，33（1）：96-100.

Wang Bojun，Wu Yongbin，Jiang Youwei，et al. Physical simulation experiments on PVT properties of foamy oil［J］. Acta Petrolei Sinica，2012，33（1）：96-100.

［23］   王玮，宫敬，李晓平.非牛顿稠油包水乳状液的剪切稀释性［J］. 石油学报，2010，31（6）：1024-1026.

Wang Wei，Gong Jing，Li Xiaoping. Shear thinning behaviors of non? Newtonian water?in?heavy?oil emulsions［J］. Acta Petrolei Sinica，2010，31（6）：1024-1026.

［24］   鹿腾，李兆敏，李松岩，等.泡沫油流变特性及其影响因素实验［J］.石油学报，2013, 34（5）：1004-1009.

Lu Teng，Li Zhaomin，Li Songyan，et al. An experimental study on rheological property and influential factors of foamy oils［J］. Acta etrolei Sinica，2013，34（5）：1004-1009.

［25］   孙晓飞，张艳玉，张贤松，等.泡沫油注气吞吐参数影响规律实验分析［J］.重庆大学学报，2013, 36（11）：115-120.

Sun Xiaofei，Zhang Yanyu，Zhang Xiansong，et al. Experimental analysis on the influence induced by parameters of nature gas huff and puff in foamy oil reservoir［J］. Journal of Chongqing University，2013，36（11）：115-120.

［26］   车洪昌.江37稠油油田注降黏剂驱油实验研究［J］.岩性油气藏，2011，23（3）：124-128.

Che Hongchang. Experimental study on oil displacement by injecting viscosity reducing agent in Jiang 37 heavy oil field［J］. Lithologic Reservoirs，2011，23（3）：124-128.

［27］   Wang Hongyang，Zeng Fanhua，Zhou Xiang. Study of non?equili?brium PVT properties of methane? and propane?heavy oil systems［R］. SPE 174498,2014.

Metrics

Viewed

Full text

Abstract

Cited

Shared

Discussed

[1]	贾红兵, 赵辉, 包志晶, 赵光杰, 毛伟, 李亚光. 水驱开发效果评价新方法及其矿场应用[J]. 岩性油气藏, 2019, 31(5): 101-107.
[2]	陈国飞，唐海，唐聪,梁毅. 预测水驱油田含水率的 Von Bertalanffy 模型[J]. 岩性油气藏, 2016, 28(1): 135-138.
[3]	徐会林，王新海,魏少波，陈岩,陈鹏 . 四川盆地高石梯磨溪区块震旦系储层敏感性实验评价[J]. 岩性油气藏, 2015, 27(2): 13-17.
[4]	霍凤斌，张涛，徐发，卢劲松. “两层·六端元”页岩评价方法在下扬子地区的应用[J]. 岩性油气藏, 2013, 25(3): 87-81.
[5]	张继风. 水驱油田开发效果评价方法综述及发展趋势[J]. 岩性油气藏, 2012, 24(3): 118-122.
[6]	王平，姜瑞忠，王公昌，梁宇. 低矿化度水驱研究进展及展望[J]. 岩性油气藏, 2012, 24(2): 106-110.
[7]	久凯，丁文龙，李春燕，曾维特. 含油气盆地古构造恢复方法研究及进展[J]. 岩性油气藏, 2012, 24(1): 13-19.
[8]	饶良玉，吴向红，李贤兵，李香玲. 苏丹层状边水油藏水平井开发效果评价与对策研究[J]. 岩性油气藏, 2011, 23(5): 106-110.
[9]	邢二涛，张云锋. 水平井开发技术在贝中区N1 段应用研究[J]. 岩性油气藏, 2010, 22(Z1): 93-95.
[10]	刘雯林. 水驱油田剩余油分布预测的岩石物理依据和方法[J]. 岩性油气藏, 2010, 22(3): 91-94.
[11]	郑雷清. 综合识别方法在低阻油气层勘探中的应用[J]. 岩性油气藏, 2007, 19(2): 71-75.

关于泡沫油黏度的若干问题

Several issues concerning foamy oil viscosity

PDF (PC)

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 11

Metrics

本文评价

推荐阅读 10